Several columns were written for the Advertiser and some people began to theorize the best way forward if the city was attacked. Less than two weeks later, Montgomery City-County Civil Defense Department said it would survey possible shelter locations in the city.īy late 1952, the people of Montgomery began to voice their opinions about the possibility of a nuclear war. The officials didn't name any cities in particular, but that announcement helped kick off a growing frenzy of civil preparedness in the face of nuclear war. That announcement was accompanied by a manual to help cities conduct block-by-block surveys and build shelters. "Potential American target cities now provide protection from possible atomic bomb attacks for only two million persons, but alterations to present buildings could boost this to give safety to 15 million people," said the Federal Civil Defense Administration in an Associated Press story from March 24, 1952. ![]() ![]() Maxwell Air Force Base's proximity frightened citizens, who were often reading international news, columns and local stories about atomic bombs, war, the USSR and civil defense.Ĭivil defense may be foreign to younger readers, but the idea that cities and states needed their own preparations in case of war used to be commonplace. Starting in the 1950s, Montgomery residents were worried about the fallout and devastation of a nuclear strike.
0 Comments
![]() This triggers our anti-spambot measures, which are designed to stop automated systems from flooding the site with traffic. Some unofficial phone apps appear to be using GameFAQs as a back-end, but they do not behave like a real web browser does.Using GameFAQs regularly with these browsers can cause temporary and even permanent IP blocks due to these additional requests. If you are using the Brave browser, or have installed the Ghostery add-on, these programs send extra traffic to our servers for every page on the site that you browse, then send that data back to a third party, essentially spying on your browsing habits.We strongly recommend you stop using this browser until this problem is corrected. The latest version of the Opera browser sends multiple invalid requests to our servers for every page you visit.The most common causes of this issue are: Your IP address has been temporarily blocked due to a large number of HTTP requests. ![]() ExFAT: Use this one when you need to transfer big files with your USB drive (4GB or higher) across Windows, macOS, and some versions of Linux.FAT32: Best for transferring a small file (under 4GB) across a large number of devices with many users.It all depends on the operating system you’re using and the size of the files you want to store in your USB drive. So, which file system should you go for, FAT32, ExFAT, or NTFS? The answer is: NOTE: A drive must be at least 512 megabytes (MB) in size to be converted to the FAT32 file system.When transferring data using a USB drive across devices, you want the best possible reliability and storage capacity possible. When the conversion is complete, click Finish.Īt a command prompt, type cvt drive: /cvt32 and then press ENTER, where drive is the drive you want to convert to the FAT32 file system.įor more information about the FAT32 file system, see the following article in the Microsoft Knowledge Base:ġ54997 Description of the FAT32 File System In the Drives box, click the drive you want to convert to the FAT32 file system.Ĭlick Next, click Next, and then click Next again. NOTE: Before you convert to the FAT32 file system, uninstall any utilities or tools that protect or encrypt the Master Boot Record (MBR) or partition table (for example, uninstall Bootlock included with Symantec Norton Your Eyes Only).Ĭlick Start, point to Programs, point to Accessories, point to System Tools, click Drive Converter (FAT32), and then click Next. To convert a drive to the FAT32 file system, use the following steps. Also, this procedure does not work if your hard disk has bad sectors. WARNING: After you convert your hard disk to FAT32, you are unable to convert it back to the original FAT system. This article describes how to convert a hard disk that uses the File Allocation Table (FAT or FAT16) file system to the FAT32 file system using Drive Converter. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |